150 W Soldering-desoldering station
DUAL DPA100 with display
1442.00 € HT
DESOLDERING STATION DUAL DPA 100 : réf 1011001009
Made of :
SEMDATA DUAL soldering thermoregulation unit
SEM DPA desoldering module
Desoldering iron 100 W
Soldering iron 50 W
SEM DPA – The “autonomous” desoldering module
Reduced space requirement: The SEM DPA module is positioned under the soldering station and protects the work surface.
Efficiency: The SEM DPA module has particularly efficient suction and a power of 100 W.
Limited cost: The standard SEM DPA module is powered and regulated by a SEMDATA DUAL soldering station.
Safety: The SEM DPA module only operates within the setpoint range. The case is antistatic.
Innovative: The SEM DPA module is perfectly suited to desoldering QFP, PLCC and SO components.
SEMDATA DUAL module:
– Regulation controlled by microprocessor
– Precise regulation of the selected temperature (± 2°C)
– Fast and precise temperature adjustment with real-time display
– Self-diagnosis of operating anomalies by displaying error messages
Three levels of programming
– Standby at a temperature of 150°C if the iron is not used for 30 minutes and/or automatic shutdown if the iron is not used for 1 hour
– Temperature lock with an access code
– OFFSET: allows the temperature of the tip to coincide perfectly with that displayed
The three programming levels of the two outputs are independent
Power supply: 230 V Secondary 24 V 50/60 Hz Insulation 4000 Volts
Autonomous desoldering module SEM DPA
– Managed by the SEMDATA DUAL station (see above)
– Antistatic housing
– Vacuum indication by vacuum gauge
– For 100W desoldering iron
– 230V 50Hz power supply
– Pump Flow: 12 l/min
– Dimensions mm: l=138 h=87 p=173
SEM DPA – Autonomous desoldering module
Reduced size : The SEM DPA module is positioned under the soldering station and preserves the work surface.
Efficiency : The SEM DPA module has a particularly powerful suction and a power of 100 W.
Limited cost : The standard DPA SEM module is powered and regulated by a SEM soldering station.
Safety : The DPA SEM module only works in the set range. The housing is antistatic.
Innovative : The SEM DPA module is ideal for desoldering QFP, PLCC and SO components.
– Vacuum indication by vacuum gauge
– For desoldering iron 50 or 100W
– Power supply 230V 50Hz
– Flow Pump : 12 l / min
– Dimensions mm : l = 138 h = 87 p = 173
SEMDATA DUAL module :
– Microprocessor controlled thermoregulation
– Accurate regulation of the selected temperature (± 2°C)
– Fast and accurate temperature adjustment with real-time display
– Self-diagnosis of malfunctions by displaying error messages
Three levels of programming
– Standby at a temperature of 150 ° C if the iron is not used during 30 minutes and / or automatic stop if the iron is not used during 1 hour
– Lock of the temperature with an access code
– Offset : allows to perfectly coordinate the temperature of the tip with that displayed
– Mains supply : 230 V
– Secondary Tension 24 V
– Insulation 4000 Volts
Desoldering iron 24701 – 100W
– Ergonomic
– Embedded control button
– Unobstructable suction system
– Accurate (short distance between the hand and the end of the nozzle)
– Easy use and maintenance
– Power 100 W (24 V) – weight 120 g – length 220 mm (excluding nozzle)
– Failure resistance / mass point <2 Ohms
– Leakage voltage at nozzle <2 mV rms
– Nozzle of the iron connected to the mass
– Non-combustible and antistatic cord
2501 soldering iron.
– Power 50 W
– 24 V voltage
– Weight 50 g
– Length 210mm with tip
– T ° from 50° to 450°C
*Supplied with tip type screwdriver 1.6 mm
Frequently bought together
Other recommended products
78 Rue Raymond Poincaré
92000 Nanterre – FRANCE
Tél. +33(0)1 40 86 00 09